지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
이용수
이 논문의 연구 히스토리 (2)
- 이 논문의 후속연구가 궁금하신가요?
- 연관 학술논문 또는 학술발표를 통해 보다 발전된 연구결과를 확인하실 수 있습니다.
- 이 논문의 연구 히스토리 확인하기
초록· 키워드
오류제보하기
In order to obtain the relation between the cutting force and the process parameters in the chamfering process for the gear of a gear shaft, analysis of the process was performed with a simplified model instead of considering the whole actual 3-dimensional cutting situation produced between cutting tool and gear. The model divided the actual situation into the accumulation of hundreds of 2-dimensional layers with a small thickness in the direction of the height of gear and derived cutting force at a cutting position by accumulating each cutting force calculated in a layer. With proposed method to analyze the cutting forces in the chamfering process, it was revealed that the cutting position and size were exactly searched to calculate the cutting force in each layer. The total cutting force was the highest in the corner where the cutter encountered the gear first during the relative motion between them. The cutting forces were changed in proportion to the cutting parameters such as feed rate and trajectory.
목차
ABSTRACT
1. 서론
2. 공구 절삭력 해석
3. 결과 및 고찰
4. 결론
REFERENCES
참고문헌 (11)
참고문헌 신청
1. [기타자료] - Kohara Gear Industry Co., Ltd / 2007 / Practical Information on Gears : 505 ~ 509
2. [학술지(정기간행물)] - Kim, S. C. / 1998 / Cutting Force Estimation Using Feed Drive and Spindle Motor Currents in Milling Process / J. of KSME 22 (11) : 2029 ~ 2038
3. [학술지(정기간행물)] - Kim, K. W. / 2002 / redicting Cutting Forces in Face Milling with the Orthogonal Machining Theory / J. of KSPE 19 (2,) : 150 ~ 157
4. [학술지(정기간행물)] - Kim, J. H. / 1994 / A Study on Optimal Design of Face Milling Cutter Geometry(I) / J. of KSME 18 (9,) : 2211 ~ 2224
6. [학술대회논문] - Kuang, J. H. / 1992 / An Estimate of Mesh Stiffness and Load Sharing Ratio of a Spur Gear Pair / 6th International Power Transmission and Gearing Conference 43 (1) : 1 ~ 9
2. [학술지(정기간행물)] - Kim, S. C. / 1998 / Cutting Force Estimation Using Feed Drive and Spindle Motor Currents in Milling Process / J. of KSME 22 (11) : 2029 ~ 2038
3. [학술지(정기간행물)] - Kim, K. W. / 2002 / redicting Cutting Forces in Face Milling with the Orthogonal Machining Theory / J. of KSPE 19 (2,) : 150 ~ 157
4. [학술지(정기간행물)] - Kim, J. H. / 1994 / A Study on Optimal Design of Face Milling Cutter Geometry(I) / J. of KSME 18 (9,) : 2211 ~ 2224
6. [학술대회논문] - Kuang, J. H. / 1992 / An Estimate of Mesh Stiffness and Load Sharing Ratio of a Spur Gear Pair / 6th International Power Transmission and Gearing Conference 43 (1) : 1 ~ 9
이 논문의 저자 정보
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2014-581-000192486