지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술대회자료
- 저자정보
- 발행연도
- 2016.12
- 수록면
- 245 - 253 (9page)
이용수
이 논문의 연구 히스토리 (2)
- 이 논문의 후속연구가 궁금하신가요?
- 연관 학술논문 또는 학술발표를 통해 보다 발전된 연구결과를 확인하실 수 있습니다.
- 이 논문의 연구 히스토리 확인하기
초록· 키워드
오류제보하기
Preliminary combustor design usually requires that an extensive number of geometrical and operational conditions be evaluated and compared. During this phase important parameters the designer sought after are typically the mass flow rate distribution through air admission holes, associated pressure losses as well as liner wall temperatures. The process is therefore iterative in nature and can become expensive in terms of engineering analysis cost considering the time required to build and execute 3D CFD models. Network codes have the potential to fill the gap during this stage of the design since they can be setup and solved in timeframes that are orders of magnitude less than comprehensive CFD models, essentially leading to cost savings since overall less time is spent on 3D simulations and rig tests. An additional advantage using this approach is that results from the network solution can be applied as boundary conditions to subsequent more detailed 3D models.
In this study a commercial flow network tool, Flownex®, was used to model a complete combustor including flow distribution, combustion and heat transfer. The integrated mass, momentum and energy balance is solved using the continuity, momentum and energy equations applied to nodes and elements. These nodes and elements are the modular building blocks, typically semi-empirical and allow users to either select appropriate built-in correlations, or to define using specific equations through scripting. Flow equations are fully compressible and applied to the gas mixture. The chemical composition of the reactants forming during combustion as well as the adiabatic flame temperature is determined from the NASA CEA package incorporated into the solution. Heat transfer mechanisms included in the model are gas-surface radiation, film convection, forced convection in ducts, surface-surface radiation, and 2D axially-symmetric conduction through solid walls. Results produced from the network were compared with test data obtained from the NASA E3 development combustor. Overall good agreement resulted, showcasing the success of the approach followed.
In this study a commercial flow network tool, Flownex®, was used to model a complete combustor including flow distribution, combustion and heat transfer. The integrated mass, momentum and energy balance is solved using the continuity, momentum and energy equations applied to nodes and elements. These nodes and elements are the modular building blocks, typically semi-empirical and allow users to either select appropriate built-in correlations, or to define using specific equations through scripting. Flow equations are fully compressible and applied to the gas mixture. The chemical composition of the reactants forming during combustion as well as the adiabatic flame temperature is determined from the NASA CEA package incorporated into the solution. Heat transfer mechanisms included in the model are gas-surface radiation, film convection, forced convection in ducts, surface-surface radiation, and 2D axially-symmetric conduction through solid walls. Results produced from the network were compared with test data obtained from the NASA E3 development combustor. Overall good agreement resulted, showcasing the success of the approach followed.
목차
ABSTRACT
1. INTRODUCTION
2. NETWORK APPROACH
3. HEAT TRANSFER MECHANISMS
4. COMBUSTION CALCULATION
5. NETWORK MODEL BACKGROUND
6. NETWORK SIMULATION CASES
7. NETWORK MODEL
8. NETWORK RESULTS
9. CONCLUSION
참고문헌
참고문헌 (0)
참고문헌 신청함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Rapid Design of Secondary Flow Geometry Using a Flow Network Modelling Approach
한국추진공학회 학술대회논문집
2016 .12
-
가스터빈 연소기의 1차원 유로망 구축 및 해석
대한기계학회 춘추학술대회
2016 .12
-
가스터빈 연소기 기본 설계 프로그램 개발
한국연소학회지
2015 .09
-
Flow Network Modeling of the Priming of Spacecraft Propulsion System
한국추진공학회 학술대회논문집
2016 .12
-
Use of Computational Fluid Dynamics for the Design and Analysis of Gas Turbine Combustors
한국추진공학회 학술대회논문집
2015 .11
-
Temperature distribution of ceramic panels of a V94.2 gas turbine combustor under realistic operation conditions
Advances in materials research : AMR
2019 .01
-
Flow Network Modelling of a Nuclear Reactor Rocket
한국추진공학회 학술대회논문집
2016 .12
-
대형가스터빈 연소기의 열유동 CFD해석
한국전산유체공학회 학술대회논문집
2017 .11
-
선회식 연소로에서 최적 공기 주입을 위한 공기분배실 수치해석
한국산학기술학회 논문지
2021 .07
-
터보팬 엔진용 코어엔진 환형 연소기의 연소 및 냉각 성능 연구 (1)
한국추진공학회 학술대회논문집
2015 .05
-
저선회 모델 연소기의 스월러 코어 막힘률에 따른 난류연소유동장에 관한 수치적 연구
한국연소학회지
2019 .12
-
Investigation on Thermoacoustic Instability in a Hydrogen Combustion System Using an Analytical Approach
Journal of Propulsion and Energy
2024 .11
-
연소실 길이에 따른 이중선회 가스터빈 모델 연소기에서 연소불안정 모드 연구
한국연소학회지
2016 .06
-
다중 노즐 연소기에서 수소-메탄 혼소에 따른 연소 특성 연구
KOSCO SYMPOSIUM 논문집
2024 .11
-
모델 가스터빈 연소기에서 다양한 변수에 따른 동적 연소특성
KOSCO SYMPOSIUM 논문집
2022 .05
-
바이오가스 적용 캐비티 매트릭스 연소기 개발
한국폐기물자원순환학회지
2021 .10
-
가스터빈 연소기 열유동 및 열전달 특성 해석
한국전산유체공학회 학술대회논문집
2016 .11
-
O₂/H₂ 화염의 초임계 조건 연소 특성 연구를 위한 모델 연소기 설계
한국수소및신에너지학회논문집
2020 .02
-
다중 모델 가스터빈 연소기의 내부 유동 및 연소불안정 현상 수치적 해석
KOSCO SYMPOSIUM 논문집
2020 .09
-
희박 예혼합 연소기에서 연료 조성이 화염전달함수 특성에 미치는 영향
한국액체미립화학회지
2015 .01
이 논문의 저자 정보
최근 본 자료
댓글(0)
0