Effect of Process Parameters on Mechanical Strength of Fabricated Parts using the Fused Deposition Modelling Method

Lan P. T. Huynh; Huy A. Nguyen; Huy Q. Nguyen; Loc K. H. Phan; Thanh T. Tran

doi:10.7736/KSPE.2019.36.8.705

추천

검색

질문

자료유형: 학술저널

저자정보: Lan P. T. Huynh (Vietnamese-German University) Huy A. Nguyen (Vietnamese-German University) Huy Q. Nguyen (Vietnamese-German University) Loc K. H. Phan (Vietnamese-German University) Thanh T. Tran (Vietnamese-German University)

저널정보: Korean Society for Precision Engineering Journal of the Korean Society for Precision Engineering Journal of the Korean Society for Precision Engineering Vol.36 No.8

발행연도: 2019.8

수록면: 705 - 712 (8page)

DOI: 10.7736/KSPE.2019.36.8.705

이용수

📌

연구주제

📖

연구배경

🔬

연구방법

🏆

연구결과

초록· 키워드

오류제보하기

This study investigated the effects of process parameters on mechanical properties of fabricated parts of the Polylactic acid (PLA) materials using fused deposition modeling (FDM) in 3D printing Technology. First, Taguchi method in the design of experiment (DOE) approach was applied to generate a design matrix of three process parameters namely; printing speed, extrusion temperature and layer thickness. A L9 array with 9 specimens was used for fabrication under various process parameters by the Builder 3D printer. Tensile test was implemented and recorded in accordance with ASTM D368 standard. Achieved data were analyzed using the Minitab software to show the effect of each process parameter on mechanical properties. Secondly, a regression model was developed to predict the trend of response in case of change in setting of parameters and estimating the optimal set of process parameters which creates the strongest FDM parts. The achieved optimum parameters were used to validate the fabricated samples for tensile testing. According to the results, the best mechanical strength of fabricated parts was achieved with printing speed of 48 mm/s, extrusion temperature of 220 degree of celsius (C) and the layer thickness of 0.15 mm. Also, the extrusion temperature was the most influencing factor on ultimate tensile stress.

#Process parameter #Design of experiments #Additive manufacturing #Fused deposition modeling (FDM) #Polylactic acid (PLA)

참고문헌 (11)

참고문헌 신청

Chen, L., He, Y., Yang, Y., Niu, S., and Ren, H., “The Research Status and Development Trend of Additive Manufacturing Technology,” The International Journal of Advanced Manufacturing Technology, Vol. 89, Nos. 9-12, pp. 3651-3660, 2017.

Lanzotti, A., Grasso, M., Staiano, G., and Martorelli, M., “The Impact of Process Parameters on Mechanical Properties of Parts Fabricated in PLA with an Open-Source 3-D Printer,” Rapid Prototyping Journal, Vol. 21, No. 5, pp. 604-617, 2015.

Sood, A. K., Ohdar, R. K., and Mahapatra, S. S., “Experimental Investigation and Empirical Modelling of FDM Process for Compressive Strength Improvement,” Journal of Advanced Research, Vol. 3, No. 1, pp. 81-90, 2012.

Basavaraj, C. K. and Vishwas, M., “Studies on Effect of Fused Deposition Modeling Process Parameters on Ultimate Tensile Strength and Dimensional Accuracy of Nylon,” IOP Conference Series: Materials Science and Engineering, Vol. 149, Paper No. 012035, 2016.

Carneiro, O. S., Silva, A. F., and Gomes, R., “Fused Deposition Modeling with Polypropylene,” Materials & Design, Vol. 83, pp. 768-776, 2015.

함께 읽어보면 좋을 논문

논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!