지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
초록· 키워드
오류제보하기
MA Al alloys are examined to determine the effects of alloying of Mg and Cu and rolling on tensile deformation behavior at 748 K over a wide strain rate range($10^{-4}-10^3/s$). A powder metallurgy aluminum alloy produced from mechanically alloyed pure Al powder exhibits only a small elongation-to-failure(${\varepsilon}_f$ < ~50%) in high temperature(748 K) tensile deformation at high strain rates(${\acute{\varepsilon}}=1-10^2/s$). ${\varepsilon}_f$ in MA Al-0.5~4.0Mg alloys increases slightly with Mg content(${\varepsilon}_f={\sim}140%$ at 4 mass%). Combined addition of Mg and Cu(MA Al-1.5%Mg-4.0%Cu) is very effective for the occurrence of superplasticity(${\varepsilon}_f$ > 500%). Warm-rolling(at 393-492 K) tends to raise ${\varepsilon}_f$. Lowering the rolling-temperature is effective for increasing the ductility. The effect is rather weak in MA pure Al and MA Al-Mg alloys, but much larger in the MA Al-1.5%Mg-4.0%Cu alloy. Additions of Mg and Cu and warm-rolling of the alloy cause a remarkable reduction in the logarithm of the peak flow stress at low strain rates (${\acute{\varepsilon}}$< ~1/s) and sharpening of microstructure and smoothening of grain boundaries. Additions of Mg and Cu make the strain rate sensitivity(the m value) larger at high strain rates, and the warm-rolling may make the grain boundary sliding easier with less cavitation. Grain boundary facets are observed on the fracture surface when ${\varepsilon}_f$ is large, indicating the operation of grain boundary sliding to a large extent during superplastic deformation.
목차
등록된 정보가 없습니다.
참고문헌 (10)
참고문헌 신청
함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Influence of Cu and Mg Content on Recrystallization Behavior in Al–Zn–Mg–Cu-Based Alloy Sheets
Metals and Materials International
2023 .06
-
유성볼밀링 및 스파크 플라즈마 소결법으로 제조한 Mo-5∼20 wt%. Cu 합금의 열적 특성
전기전자재료학회논문지
2016 .01
-
Utilization of Hot Deformation to Trigger Strain-Induced Boundary Migration, Particle-Stimulated Nucleation, and Influence of Nano-Precipitates on Mechanical Properties in High-Alloyed Al–Zn–Mg–Cu Alloys
Metals and Materials International
2024 .08
-
Bimodal-Structured Al?Mg Alloy with High Strength and Ductility Processed by High Strain Rate Rolling at Medium Temperature
Metals and Materials International
2021 .12
-
Al-Mg-Si 합금의 열처리와 Cu 첨가에 따른 미세구조 및 전기화학적 거동에 대한 연구
한국소성가공학회 학술대회 논문집
2024 .10
-
Hot Tensile Deformation Behavior of Twin Roll Casted 7075 Aluminum Alloy
Metals and Materials International
2015 .01
-
Microstructure, Mechanical Properties and Tribological Behavior of Two-Phase Mg–Y–Cu Alloys with Long Period Stacking Ordered Phases
Metals and Materials International
2021 .01
-
Effects of Warm Rolling Deformation on the Microstructure and Ductility of Large 2219 Al–Cu Alloy Rings
Metals and Materials International
2020 .01
-
항공기 엔진 부품용 고강도 Al-Zn-Mg-Cu계 합금 개발
한국소성가공학회 학술대회 논문집
2024 .10
-
A study on process design on warm forging of differential gear cover with Al-Mg-Si-Cu alloy
한국소성가공학회 학술대회 논문집
2015 .05
-
ECO Mg(with CaO)을 첨가한 고강도·고연신 Al-Mg(7, 9wt.%) 합금의 미세조직 및 인장 변형 거동
한국소성가공학회 학술대회 논문집
2018 .05
-
고엔트로피합금의 고변형률속도 초소성
한국소성가공학회 학술대회 논문집
2021 .05
-
A356 합금 내 미량의 Mg/Cu 첨가 및 열처리조건에 따른 미세조직 및 기계적 성질 변화
한국생산제조학회 학술발표대회 논문집
2020 .12
-
Effects of Interactions Among Alloying Elements on the Microstructure, Phase Transitions, and Electrical Resistivity of the Cu81Al19 Alloy
Metals and Materials International
2022 .08
-
Nucleation Mechanism of Discontinuous Dynamic Recrystallization with Restrained Grain Boundary Sliding
Metals and Materials International
2021 .12
-
박판주조 및 압연 공정을 이용한 고강도 Al-Zn-Mg-Cu 합금 판재제조
한국소성가공학회 학술대회 논문집
2019 .10
-
Effect of Grain and Secondary Phase Morphologies in the Mechanical and Damping Behavior of Al7075 Alloys
Metals and Materials International
2016 .01
-
Al-4.0%Zn-1.5%Mg-0.9%Cu 합금의 압출, 압연 및 열처리에 따른 미세조직 변화
열처리공학회지
2018 .01
-
냉간압연가공에 따른 Al-5.5Mg-2.9Si계와 Al-7Mg-0.9Zn계 합금의 압연가공성 및 기계적 특성 차이
한국재료학회지
2016 .01
-
Development of Ultrafine Grain Structure in an Al–Mg–Mn–Sc–Zr Alloy During High-Temperature Multidirectional Isothermal Forging
Metals and Materials International
2021 .01
이 논문의 저자 정보
최근 본 자료
댓글(0)
0