지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2022.8
- 수록면
- 179 - 185 (7page)
이용수
초록· 키워드
오류제보하기
The influence of post-roll bonding heat treatment conditions such as temperature and time on the variation in the diffusion layer, generated at the bonding interface and the subsequent mechanical properties of the roll-bonded Ti grade 1/Al1050/Ti grade 1 sheets, was systematically investigated. The intermetallic compound (IMC) phase generated by post heat treatment conditions adopted in this study was obviously indexed as monolithic TiAl₃. Whereas the thickness of IMC layer generated by annealing at 500 ℃ was approximately 100 nm scale, it drastically increased above 1.5 ㎛ when annealed at 600 ℃. Uniaxial tensile and peel tests were then performed to compare mechanical properties. As a result, the bonding strength drastically increased above 7.9 N/mm by annealing at 600 ℃, which implies that proper annealing condition was a prerequisite, to improving interface bonding strength as well as global elongation properties for Ti/Al/Ti 3-ply sheet.
목차
Abstract
1. 서론
2. 실험 방법
3. 결과 및 고찰
4. 결론
REFERENCES
참고문헌 (14)
참고문헌 신청
J. Lacaze, S. Tierce, M. C. Lafont, Y. Thebault, N. Pébère, G. Mankowski, C. Blanc, H. Robidou, D. Vaumousse and D. Daloz, 2005, Study of the microstructure resulting from brazed aluminum materials used in heat exchangers, Mater. Sci. Eng. A, vol. 413, pp. 317-321. https://doi.org/10.1016/j.msea.2005.08.187
K.S. Lee, Y.S. Lee, Y.N. Kwon, 2014, Influence of Secondary Warm Rolling on the Interface Microstructure and Mechanical Properties of a Roll-Bonded Three-Ply Al/Mg/Al Sheet, Mater. Sci. Eng. A, vol. 606, pp. 205- 213. https://doi.org/10.1016/j.msea.2014.03.082
X. Li, G. Zu, M. Ding, Y. Mu, P. Wang, 2011, Interfacial microstructure and mechanical properties of Cu/Al clad sheet fabricated by asymmetrical roll bonding and annealing, Mater. Sci. Eng. A, vol 529, pp. 485-491. https://doi.org/10.1016/j.msea.2011.09.087
P.P. Gudur, M.A. Salunkhe, U.S. Dixit, 2007, A theoretical study on the application of asymmetric rolling for the estimation of friction, Int. J. Mech. Sci., vol 50, pp. 315-327. https://doi.org/10.1016/j.ijmecsci.2007.06.002
K.X. Liu, W.D. Liu, J.T. Wang, H.H. Yan, X.J. Li, Y.J. Huang, X.S. Wei, J. Shen, 2008, Atomic scale bonding of bulk metallic glass to crystalline aluminum, Appl. Phys. Lett., vol. 93, 081918. https://doi.org/10.1063/1.2976667
K.S. Lee, Y.S. Lee, Y.N. Kwon, 2014, Influence of Secondary Warm Rolling on the Interface Microstructure and Mechanical Properties of a Roll-Bonded Three-Ply Al/Mg/Al Sheet, Mater. Sci. Eng. A, vol. 606, pp. 205- 213. https://doi.org/10.1016/j.msea.2014.03.082
X. Li, G. Zu, M. Ding, Y. Mu, P. Wang, 2011, Interfacial microstructure and mechanical properties of Cu/Al clad sheet fabricated by asymmetrical roll bonding and annealing, Mater. Sci. Eng. A, vol 529, pp. 485-491. https://doi.org/10.1016/j.msea.2011.09.087
P.P. Gudur, M.A. Salunkhe, U.S. Dixit, 2007, A theoretical study on the application of asymmetric rolling for the estimation of friction, Int. J. Mech. Sci., vol 50, pp. 315-327. https://doi.org/10.1016/j.ijmecsci.2007.06.002
K.X. Liu, W.D. Liu, J.T. Wang, H.H. Yan, X.J. Li, Y.J. Huang, X.S. Wei, J. Shen, 2008, Atomic scale bonding of bulk metallic glass to crystalline aluminum, Appl. Phys. Lett., vol. 93, 081918. https://doi.org/10.1063/1.2976667
함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Influence of post-heat treatment on the interface-correlated bonding properties of roll-bonded 3-ply Ti/Al/Ti metallic sheets
한국소성가공학회 학술대회 논문집
2021 .11
-
A study on deducing optimal heat-treatment condition correlated to the generation of intermetallic compounds at joint interface of a Ti/Al/Ti 3-ply clad sheet
한국소성가공학회 학술대회 논문집
2022 .05
-
A Study on the improvement of bonding property for Al/Ti dissimilar metallic sheets
한국소성가공학회 학술대회 논문집
2022 .12
-
Ti-3Al-2.5V 튜브의 초소성성형/확산접합에서 접합계면 특성
한국소성가공학회 학술대회 논문집
2016 .04
-
Ti-3Al-2.5V 튜브의 초소성 하이드로포밍과 확산접합으로 제조된 T형 구조물의 접합 특성 분석
열처리공학회지
2018 .01
-
Effect of Volume Fraction of Ti on Microstructure Evolution and Thermal Properties of Al/Ti Laminated Composites
Metals and Materials International
2024 .04
-
Microstructure and Mechanical Features of Electron Beam Welded Dissimilar Titanium Alloys: Ti–10V–2Fe–3Al and Ti–6Al–4V
Metals and Materials International
2019 .01
-
Heat treatment for enhancing impact toughness and fatigue cycle of Ti-6Al-4V joint
대한용접학회 특별강연 및 학술발표대회 개요집
2024 .10
-
A Study of Electron Beam Welding Ratios on Dissimilar Titanium Alloys : Ti-10V-2Fe-3Al and Ti-6Al-4V
대한용접학회 특별강연 및 학술발표대회 개요집
2019 .05
-
Ti-6A-4V합금 후판 압연 공정 연구
한국소성가공학회 학술대회 논문집
2022 .12
-
Effects of Y and Ti addition on microstructure stability and tensile properties of reduced activation ferritic/martensitic steel
Nuclear Engineering and Technology
2019 .01
-
Ti-Based Solid Solution Carbonitrides Prepared From Ti-Alloy Scraps via a Hydrogenation-Dehydrogenation Process and High-Energy Milling
Metals and Materials International
2015 .01
-
유한요소법을 이용한 Ti-6Al-4V 의 선삭가공 최적화에 관한 연구
한국CDE학회 학술발표회 논문집
2015 .02
-
Determination of Optimal Weld Parameter for Joining Titanium Alloys by Gas Tungsten Arc Welding using Taguchi Method
대한용접·접합학회지
2021 .02
-
Evaluation of Bonding Strength Regarding Sample Size by Die Shear Testing for Cu/Ti/Cu Bonded Material
한국소성가공학회 학술대회 논문집
2022 .12
-
Electrochemical and Spectroscopic Study on the Corrosion of Ti–5Al and Ti–5Al–5Cu in Chloride Solutions
Metals and Materials International
2019 .01
-
Microstructure and Refinement Performance of Al-Ti-C Master Alloy: Effect of Excess Ti on the Growth and Nucleating Ability of TiC Particles
Metals and Materials International
2017 .01
-
α-Al₂Ou₃ / STS 430 브레이징을 위한 Cu-Al-Ti 삽입금속 개발 및 접합부 기계적 성질에 미치는 Ti 함유량의 영향
대한용접학회 특별강연 및 학술발표대회 개요집
2016 .04
-
High Cycle Fatigue Characteristics of PBF Ti-6Al-4V Sheet
한국소성가공학회 학술대회 논문집
2024 .10
-
Ti-6Al-4V 합금의 미세구조 분석
한국결정성장학회지
2016 .01
이 논문의 저자 정보
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2022-551-001618939