지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 저널정보
- 한국콘크리트학회 International Journal of Concrete Structures and Materials International Journal of Concrete Structures and Materials Vol.18 No.6
- 발행연도
- 2024.11
- 수록면
- 1,183 - 1,194 (12page)
이용수
초록· 키워드
오류제보하기
To investigate the response of post-installed rebar connectors in steel frame retrofitted concrete structures under combined shear and tension, seven shear-and-tensile tests were conducted. The bearing capacity, stiffness, and hysteresis behavior of the connectors were investigated during the tests. Both Monotonic and cyclic load regimes were applied in the loading process. The results show that with the increase of the loading angle, the deformation capacity, the yield force, ultimate tensile force, and tensile stiffness of the specimen decrease, while the maximum shear force and shear stiffness of the specimen increase. The bearing capacity, stiffness, and energy dissipation performance of the specimen under a monotonic load is greater than that under the coupled shear-and-pull load. The bearing capacity, stiffness, hysteresis curve, and failure status of the specimens are not affected by different loading regimes. At the end, the design formula of anchor bolt for this type of connectors from the design code of China, United States, and Japan were compared. Formulas to calculate the shear strength under combined shear and tension is developed.
목차
Abstract
1. Introduction
2. Test Setup
3. Loading Method and Instrumentation
4. Test Results
5. Design Formula of Anchor Bolt
6. Shear‑Resistant of the Post‑installed Rebar
7. Conclusion
References
참고문헌 (0)
참고문헌 신청함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
단속배치된 캡 형상의 전단연결재의 전단내력에 관한 실험 연구
한국공간구조학회지
2018 .01
-
Experimental study on the hybrid shear connection using headed studs and steel plates
Steel and Composite Structures, An International Journal
2020 .01
-
Investigation of pipe shear connectors using push out test
Steel and Composite Structures, An International Journal
2018 .01
-
Distribution of shear force in perforated shear connectors
Steel and Composite Structures, An International Journal
2018 .01
-
Monotonic behavior of C and L shaped angle shear connectors within steel-concrete composite beams: an experimental investigation
Steel and Composite Structures, An International Journal
2020 .01
-
Application of ANFIS technique on performance of C and L shaped angle shear connectors
Smart Structures and Systems, An International Journal
2018 .01
-
Experimental Research on the Shear Connectors in Foam Concrete with C‑Channel Embedment
International Journal of Concrete Structures and Materials
2018 .07
-
Application of ANFIS technique on performance of C and L shaped angle shear connectors
Smart structures and systems
2018 .01
-
Interfacial shear resistance of angle shear connectors welded to concrete filled U-shaped CFS beam
Steel and Composite Structures, An International Journal
2022 .05
-
Static and fatigue behavior of through-bolt shear connectors with prefabricated HFRC slabs
Structural Engineering and Mechanics, An Int＇l Journal
2022 .07
-
Behavior of steel-concrete composite beam using angle shear connectors at fire condition
Steel and Composite Structures, An International Journal
2019 .01
-
500㎫ 벽체전단철근의 최소철근량에 대한 실험적 연구
대한건축학회 논문집 - 구조계
2016 .08
-
FEM Analysis of RC Deep Beam Depending on Shear-Span Ratio
ARCHITECTURAL RESEARCH
2017 .12
-
Shear behavior of composite frame inner joints of SRRC column-steel beam subjected to cyclic loading
Steel and Composite Structures, An International Journal
2018 .01
-
Seismic behavior of double steel plates and concrete filled composite shear walls subject to in-plane cyclic load: Experimental investigation
Structural Engineering and Mechanics, An Int＇l Journal
2024 .05
-
Seismic behavior of T-shaped steel reinforced high strength concrete short-limb shear walls under low cyclic reversed loading
Structural Engineering and Mechanics, An Int＇l Journal
2016 .01
-
Pressure-Assisted Sinter-Bonding Characteristics at 250 °C in Air Using Bimodal Ag-Coated Cu Particles
Electronic Materials Letters
2020 .01
-
Structural performance of steel-concrete composite bridges utilising innovative blind bolt shear connectors
Steel and Composite Structures, An International Journal
2021 .01
-
Analyzing shear strength of steel-concrete composite beam with angle connectors at elevated temperature using finite element method
Steel and Composite Structures, An International Journal
2021 .09
-
Shear transfer mechanism in connections involving concrete filled steel columns under shear forces
Steel and Composite Structures, An International Journal
2018 .01
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-151-25-02-091139597